EN
id
sk
sr
sv
it
pt
bn
ms
be
nl
fr
th
vi
ru
ja
ko
de
hy
az
bs
bg
my
cs
da
dv
el
et
fil
fi
ga
gl
gn
he
hi
km
hr
hu
is
kn
rw
lo
lv
lt
lb
lg
mi
mt
ne
no
ny
or
om
per
pl
ro
sa
so
es
sw
ta
tr
uk
ur
cy
xh
An ASM SIPLACE 16mm feeder part number should never be treated as the complete purchasing specification. A feeder quotation may show a familiar reference while omitting the revision suffix, sensor-related configuration, feeder family, target machine interface, physical condition or functional test status of the supplied unit.
For buyers searching for an ASM 16mm feeder, SIPLACE 16mm feeder, 00141272 feeder, 00141292 feeder, 00141372 feeder, 00141392 feeder, 00141572 feeder or 00141672 feeder, the important question is not only whether the quoted part number appears correct.
The real question is whether the exact feeder label, revision suffix, sensor or splice-related hardware, target machine family, mechanical interface, tape path and operating condition match the production line where the feeder will be installed.
In Brief: What Should Be Verified Before Ordering an ASM SIPLACE 16mm Feeder?
Before ordering an ASM SIPLACE 16mm feeder, verify the complete part number, visible suffix, feeder family, target placement-machine model, sensor or splice-related configuration, tape path, cover tape route, latch, connector, machine recognition and controlled feed-test result.
Do not approve a feeder based only on a base part number.
Do not assume every 16mm feeder is interchangeable across SIPLACE machine families.
Do not assume a sensor or splice feature is installed unless it appears on the actual feeder.
Do not treat a clean feeder as production-ready without tape-feed verification.
Why a 16mm Feeder Part Number Is Not the Full Specification
A feeder part number is an important identification point, but it does not define every detail of the physical feeder. Two feeders with similar-looking references may differ in revision suffix, sensor hardware, machine interface, feeder electronics, latch condition, tape path, cover tape handling or included accessories.
This matters because a feeder can appear similar to an installed production feeder while still being unsuitable for the target machine, feeder slot, software environment or component-tape route.
Verification principle: Confirm the complete feeder identity before confirming compatibility.
16mm Feeder Reference Groups to Verify
| Reference Group | Part Numbers | What Must Be Confirmed Before Purchase |
|---|---|---|
| 16mm High-Speed Feeder References | 00141272, 00141372 | Complete suffix, feeder family, target machine, tape path, latch, connector and controlled tape-feed result. |
| 16mm Sensor / Splice-Related References | 00141292, 00141392 | Actual installed sensor-related hardware, visible suffix, interface, connector condition, machine recognition and functional evidence. |
| 16mm E Series Procurement References | 00141572, 00141672 | Target E Series machine, complete label, feeder slot, mechanical interface, tape path and real feed-test result. |
Why Revision Suffixes Matter
ASM feeder references are often quoted as a basic number only. However, the visible suffix can identify a version, production revision, supplied configuration or feature variation. Before purchase, request the complete reference exactly as displayed on the feeder label.
Do not approve a quotation that lists only 00141272, 00141392 or 00141572 when the actual feeder label includes additional suffix information. The quotation, physical photos and shipment label should match.
Request These Before Approving a Quote
Clear close-up photo of the feeder part-number label
Full visible part number and revision suffix
Current front and rear feeder photos
Photo of the tape path and sprocket area
Photo of cover tape guide and take-up area
Photo of latch, connector and mounting interface
Photo of sensor or splice-related hardware where claimed
Target-machine compatibility confirmation
Controlled tape-feed test result or video
00141272 vs 00141292: What Must Be Checked?
When comparing 00141272 and 00141292 quotations, do not assume that the difference is limited to a label or a simple feature option. Confirm the complete visible reference, sensor-related hardware, feeder interface, target machine family and physical feeder condition.
For a production replacement, request actual feeder photos rather than catalog images. The tape path, sprocket condition, cover tape route, connector and latch should all be checked before approval.
00141372 vs 00141392: SmartFeeder and Sensor Verification
When 00141372 or 00141392 appears in a quote, the supplier should confirm the exact installed feeder configuration. Do not treat a SmartFeeder-related description as proof that the feeder includes every expected option or that it is automatically compatible with the target machine.
Verify the part-number label, actual sensor or splice-related module where applicable, connector condition, machine interface, tape path and controlled feed behavior.
E Series 00141572 and 00141672 Replacement Checks
E Series replacement work requires its own compatibility review. Even when a feeder is listed as 16mm, the replacement decision should not be based only on tape width or exterior appearance.
For 00141572 or 00141672 procurement requests, confirm the target E Series machine, feeder slot, latch, connector, mechanical interface, tape path and feeder-recognition requirement before purchase.
Where 00141672 appears in a quotation or inventory list, treat it as a reference that requires feeder-level verification. Do not assume it is a direct equivalent to another 16mm E Series feeder without matching the complete label, physical interface and test result.
Standard Feeder vs Sensor or Splice-Related Configuration
A standard 16mm feeder should be reviewed for feeder identity, tape path, sprocket movement, cover tape route, reel seating, latch and machine recognition. A sensor or splice-related feeder requires all of those checks plus verification of the actual installed sensor-related module and its target-machine setup.
| Review Area | Standard 16mm Feeder | Sensor or Splice-Related Configuration |
|---|---|---|
| Feeder Identity | Confirm full part number, suffix and target machine family. | Confirm full part number, suffix and installed sensor-related hardware. |
| Tape Path | Check guide, sprocket, cover tape route and indexing movement. | Check the same tape path plus sensor-area condition and related cables. |
| Machine Recognition | Confirm feeder slot, interface and recognition. | Confirm feeder recognition plus required sensor-related configuration. |
| Production Release | Run controlled tape advance and first-article verification. | Run the same checks plus any required sensor or splice validation. |
16mm Feeder RFQ Verification Checklist
Confirm the complete feeder part number and visible suffix.
Confirm whether the feeder is standard, sensor-related or splice-related.
Record the target ASM SIPLACE machine model and feeder slot.
Request front, rear, label, latch and connector photos.
Inspect tape guide, sprocket and cover tape route.
Confirm reel support and tape-loading direction.
Verify the physical condition of sensor-related hardware where applicable.
Confirm feeder recognition on the target machine where possible.
Run representative tape through the feeder.
Verify component pocket presentation at the pickup position.
Complete first-article placement verification before full production release.
What a Useful 16mm Feeder Acceptance Test Should Prove
A feeder acceptance test does not need to reproduce an entire SMT production run. However, it should prove that the quoted feeder is identifiable, mechanically stable and capable of advancing tape consistently through its installed path.
The feeder label matches the quotation.
The housing, latch and connector area are intact.
The tape path is clean and free of major obstruction.
The sprocket or advance mechanism operates consistently.
Cover tape routing behaves correctly.
Representative tape advances without abnormal resistance.
Component pockets arrive at the expected pickup position.
Sensor-related hardware is verified where included.
Common 16mm Feeder Part Number Mistakes
Mistake 1: Matching Only the Base Part Number
A basic reference may not identify the exact version or supplied configuration. Always check the visible suffix and actual feeder label.
Mistake 2: Treating 16mm Width as Full Compatibility Proof
Tape width is only one identification point. Feeder family, slot interface, connector, sensor configuration, latch design and machine recognition must also be verified.
Mistake 3: Assuming Sensor Function From a Listing Title
Supplier descriptions should be supported by photos, configuration records and functional evidence from the actual feeder.
Mistake 4: Skipping Functional Feed Testing
A feeder may look clean but still have tape-path, sprocket, cover tape, latch or connector issues that only appear with real tape.
Related ASM Feeder Resources
Frequently Asked Questions About ASM SIPLACE 16mm Feeder Part Numbers
Can I buy an ASM 16mm feeder based only on the base part number?
No. Confirm the complete part number, revision suffix, feeder family, interface, physical condition and functional feed-test status before purchase.
Does every 16mm feeder fit every SIPLACE machine?
No. Tape width alone does not prove compatibility. The feeder family, slot interface, target machine and feeder-recognition requirement must also be confirmed.
Why is the revision suffix important?
The suffix can identify a specific version, revision or supplied configuration. It should be checked against the actual feeder label and quotation.
How can I verify sensor or splice-related feeder hardware?
Request close-up photos of the related module, feeder label, connector area and functional test evidence where available.
Can 00141572 and 00141672 be treated as direct replacements?
No. Confirm the complete feeder label, target E Series machine, physical interface, latch, connector and controlled feed-test result before approving a replacement.
Can a used 16mm feeder look clean but still fail in production?
Yes. Tape-path wear, sprocket issues, cover tape problems, latch damage, sensor faults or recognition issues may not be visible in a basic product photo.
Need Help Verifying an ASM SIPLACE 16mm Feeder?
Share the complete part number, visible suffix, target machine model, feeder photos and required production setup. A practical review should confirm the actual feeder identity before a replacement or inventory purchase is approved.
