EN
id
sk
sr
sv
it
pt
bn
ms
be
nl
fr
th
vi
ru
ja
ko
de
hy
az
bs
bg
my
cs
da
dv
el
et
fil
fi
ga
gl
gn
he
hi
km
hr
hu
is
kn
rw
lo
lv
lt
lb
lg
mi
mt
ne
no
ny
or
om
per
pl
ro
sa
so
es
sw
ta
tr
uk
ur
cy
xh
An ASM SIPLACE 8mm feeder part number should never be treated as the full purchasing specification. A feeder quotation can show a familiar number while omitting the revision suffix, sensor configuration, feeder family, physical interface, actual machine compatibility or condition of the supplied unit.
For buyers searching for an ASM 8mm feeder, SIPLACE 8mm feeder, 00141270 feeder, 00141290 feeder, 00141370 feeder, 00141390 feeder, 00141480 feeder, 00141490 feeder, 00141500 feeder, 00141700 feeder or 00141570 feeder, the most important question is not only whether the quoted number looks correct.
The important question is whether the exact feeder version, revision suffix, machine family, sensor configuration, tape path, mechanical interface and physical condition match the production line where it will be installed.
In Brief: What Should Be Verified Before Ordering an ASM SIPLACE 8mm Feeder?
Before ordering an ASM SIPLACE 8mm feeder, verify the complete part number, revision suffix, feeder family, tape width configuration, sensor or splice-related setup, machine interface, actual feeder photos, mechanical condition and functional feed test status.
Do not approve a feeder based only on a base part number.
Do not assume all 8mm feeders are interchangeable across SIPLACE machine families.
Do not assume a sensor or splice description is included unless it appears in the written configuration.
Do not assume a clean feeder is ready for stable production without a tape-feed test.
Why an ASM 8mm Feeder Part Number Is Not the Full Specification
A feeder part number is an important starting point, but it is only one layer of identification. In real SMT procurement, two feeders with similar reference numbers may differ in revision suffix, sensor configuration, tape path condition, electronics, interface details, mechanical latch condition or included accessories.
This matters because a feeder can physically fit into a feeder cart or look similar to an existing unit while still being the wrong configuration for the machine, software environment or component tape route.
Verification principle: Confirm the complete feeder identity before confirming compatibility.
High-Speed 8mm Feeder References to Verify
The following references are commonly encountered in high-speed ASM SIPLACE 8mm feeder quotations and inventory lists. They should be verified against the full suffix, physical label and target machine before purchase.
| Reference Group | Part Numbers to Verify | What Must Be Confirmed |
|---|---|---|
| 8mm High-Speed Feeder References | 00141270, 00141370, 00141500 | Exact feeder family, revision suffix, mechanical condition, machine interface and tape-feed function. |
| 8mm Sensor / Splice-Related References | 00141290, 00141390, 00141490 | Actual sensor or splice-related configuration, complete suffix, functional status and machine recognition. |
| Other High-Speed References Requiring Direct Verification | 00141480, 00141700 | Full feeder label, actual width configuration, installed modules, interface type and supplier test evidence. |
| E Series 8mm Feeder Reference | 00141570 | E Series compatibility, feeder slot interface, actual tape-feed behavior and condition of the offered unit. |
Why Revision Suffixes Matter
A base part number may be followed by a revision suffix such as -01, -02, -03, -04 or another production-specific designation. The suffix can matter because it may identify a version, revision, sensor variation, supplied configuration or manufacturing update.
Before buying an ASM feeder, request the complete part number exactly as shown on the feeder label. Do not rely on a quotation title that lists only the base number.
Request These Before Approving a Quote
Clear feeder nameplate photo
Full visible part number and revision suffix
Photo of the tape path and sprocket area
Photo of the feeder connector and latch area
Photo of any sensor, sensor cable or related module
Machine compatibility statement from the supplier
Functional tape-feed or advance test evidence
How X, Sensor and E Series References Should Be Treated
Feeder family references are useful for narrowing the search, but they should not replace machine-level verification. An 8mm feeder can be associated with a particular SIPLACE family, but the final approval should still include the full part number, feeder label, slot interface, software recognition and controlled test on the target machine where possible.
For E Series replacement work, the same rule applies. The tape width alone does not prove direct replacement capability. The exact feeder family, machine interface, mechanical condition and feeder recognition must be confirmed.
Standard Feeder vs Sensor or Splice-Related Configuration
Some 8mm feeder quotations include wording such as sensor, splice sensor, smart feeder or similar descriptors. These terms should be treated as configuration claims that require verification, not as assumptions based only on feeder appearance.
Before approving a sensor-related feeder, confirm whether the physical sensor module is present, whether the quoted feeder is recognized correctly by the machine, whether the required sensor function is active and whether the component tape route has been tested.
Seven Photos to Request Before Buying an ASM 8mm Feeder
Full feeder front view
Full feeder rear view
Part-number label and revision suffix
Tape path and sprocket area
Cover tape guide and take-up area
Connector, latch and feeder interface area
Sensor or splice-related module, where applicable
These images make it much easier to identify incorrect listings, incomplete feeder assemblies, damaged tape paths, missing modules or mismatched supplier descriptions.
Part Number Verification Checklist
| Verification Area | What to Confirm | Why It Matters |
|---|---|---|
| Complete Part Number | Base number plus revision suffix. | Helps avoid receiving a different version from the quoted feeder. |
| Feeder Family | Target machine family and feeder interface. | 8mm width alone does not prove direct compatibility. |
| Sensor Configuration | Actual installed sensor or splice-related module. | Prevents assumptions based on listing titles. |
| Tape Path | Sprocket, guide, cover tape route and take-up condition. | Determines whether the feeder can move tape consistently. |
| Mechanical Interface | Latch, housing, connector and feeder slot condition. | Prevents installation and recognition problems. |
| Functional Test | Tape advance, feed sequence and machine recognition. | Confirms the feeder is more than visually complete. |
Common Part Number Identification Mistakes
Mistake 1: Matching Only the First Eight Digits
A base part number may not identify the exact revision or supplied configuration. Always verify the complete visible reference on the feeder label.
Mistake 2: Treating 8mm Width as Full Compatibility Proof
Tape width is only one feature. Feeder series, interface, sensor configuration, latch design and machine recognition must also be checked.
Mistake 3: Assuming Sensor Function From a Listing Title
A supplier description should be supported by photos and a configuration list. Confirm the actual installed sensor-related hardware and functional status.
Mistake 4: Skipping the Tape-Feed Test
A feeder can look clean and still have indexing, tape path, cover tape or mechanical advance issues. A controlled tape-feed check is more useful than appearance alone.
Related ASM 8mm Feeder Resources
Frequently Asked Questions About ASM SIPLACE 8mm Feeder Part Numbers
Can I buy an ASM 8mm feeder based only on the base part number?
No. Confirm the complete part number, revision suffix, feeder family, interface, configuration, physical condition and functional test status before purchase.
Does an 8mm feeder always fit every SIPLACE machine?
No. Tape width alone does not prove compatibility. The feeder family, slot interface, machine configuration and feeder recognition must also be confirmed.
Why is the revision suffix important on an ASM feeder?
The suffix can identify a version, revision or supplied configuration. It should be checked against the physical feeder label and written quotation.
How can I verify whether a sensor-related feeder is actually supplied with the required module?
Request close-up photos of the module, feeder label, connector area and a functional machine-recognition or tape-feed test where possible.
What is the fastest way to confirm an ASM 8mm feeder before purchase?
Compare the full visible feeder label, target machine model, required configuration, supplier photos and tape-feed test results before payment or shipment.
Can a used 8mm feeder be visually clean but still fail in production?
Yes. Tape path wear, indexing issues, cover tape problems, sensor faults, latch damage or recognition problems may not be visible in a basic product photo.
Need Help Verifying an ASM SIPLACE 8mm Feeder Part Number?
Share the complete part number, revision suffix, target machine model, feeder photos and required production configuration. A useful review should confirm the actual feeder identity before a replacement or inventory purchase is approved.
